リトルタイドのバイアルの溶解:計算
The four steps, three worked examples and a calculator for lyophilized research vials. Bench arithmetic, not guidance on use.
5 分で読めます · 2026-11-17
The four steps, three worked examples and a calculator for lyophilized research vials. Bench arithmetic, not guidance on use.
5 分で読めます · 2026-11-17
溶解(再溶解)とは、凍結乾燥(フリーズドライ)された製品に希釈液を加え、再び溶液にすることです 13。リトルタイドの研究用バイアルは、密封されたバイアルに入った凍結乾燥粉末として供給されます。
この計算に出典は必要ありません。濃度は、バイアル内の質量を加えた液量で割ったものです。ある質量を含む液量は、その質量を濃度で割ったものです。
粉末から測定された試料まで
The same four steps for any lyophilized vial. Laboratory handling, not use in a person.
1. バイアルのラベルを読む
ラベルには、バイアル内のペプチドの質量がミリグラム単位で記載されています。この数値が、すべての計算の出発点です。
2. 希釈液を加える
計量した量の希釈液を、ガラス壁を伝わせてゆっくり加えます。やさしく回し混ぜてください。振るとペプチドを損なうおそれがあります。
3. 濃度を求める
Concentration is mass divided by volume: 10 mg in 2 mL is 5 mg per mL.
4. 試料の量を測る
必要な体積は、必要な質量を濃度で割ったものです。U-100注射器では、1 mLが100単位です。
A 10 mg vial with 2 mL of diluent is 5 mg per mL. A 1 mg sample is then 0.2 mL, which reads as 20 units on a U-100 syringe.
A 20 mg vial with 2 mL is 10 mg per mL. A 4 mg sample is 0.4 mL, or 40 units.
A 30 mg vial with 3 mL is also 10 mg per mL. A 12 mg sample would be 1.2 mL, more than a 1 mL syringe holds. That is why the volume of diluent is chosen with the sample in mind: less diluent makes a stronger solution and a smaller volume to measure.
これらの例の量は、第2相プロトコルが試験群に割り当てた週あたりの量です1、2。出版された研究と照らし合わせて計算を確認できるように使っています。いかなる種類の推奨でもありません。
Draw to
10 units
0.1 mL on a U-100 syringe
20 mg in 2 mL is 10 mg/mL. 1 mg of that is 0.1 mL, which reads as 10 units. This is arithmetic for a vial of Retatrutide; no amount here is a recommendation.
凍結乾燥ペプチドの一般的な取り扱いは、密封したバイアルを冷凍または冷蔵し、乾燥させて光を避けることです。また、サプライヤーの分析証明書に従ってください。試験報告書には、レタトルチド自身の試験用供給品がどのように保管されたかは記載されていません。
ペプチドを溶液に戻した後は冷蔵保存し、サプライヤーが示す期間内に使い切ります。複数回にわたって中身を取り出すバイアルには、保存剤入りの希釈液が必要です13。
The numbers are those of the Retatrutide page, where every source is listed.